IS200BPIIH1AAA
GE
Overview
The IS200BPIIH1AAA is an automation component from GE. It is part of GE's industrial automation product portfolio.
Application & Technical Notes
As an automation component, the IS200BPIIH1AAA is intended for deployment in panel-based control cabinets and machine enclosures where the GE product portfolio equipment is installed. It performs a defined automation function within the control system and is selected to match the installed GE platform.
Specific electrical and mechanical ratings depend on the exact configuration and suffix of the part; the original datasheet should be consulted for the definitive specification.
Maintenance & Diagnostics
Inspect terminals and connectors for corrosion or looseness, and confirm the module seats correctly in its carrier. Always de-energise the circuit and follow lock-out/tag-out before handling; refer to the official instruction bulletin for service procedures.
Sourcing & Procurement
When sourcing the IS200BPIIH1AAA, distinguish three supply tiers: (1) genuine GE stock from an authorised distributor; (2) compatible equivalents or surplus/NOS (new-old-stock) from third parties; (3) alternative parts offering equivalent function. Genuine supply carries the full warranty and traceability; compatible or alternative items may be cheaper but should be validated for form, fit, firmware and certification before use in a live system. PLCXpert publishes this page as an independent reference and does not sell the part — verify every claim with the manufacturer or your distributor.
Confirm mechanical and electrical compatibility with your GE product portfolio installation and the intended function. Lead times and pricing vary by region and lifecycle status; obtain a current quote from an authorised channel rather than relying on stale listings.
Check live stock, lead time and request a quote for IS200BPIIH1AAA (opens in a new tab)
Frequently Asked Questions
What is the IS200BPIIH1AAA?
The IS200BPIIH1AAA is an automation component from GE. It belongs to GE's automation product portfolio.
What are the key technical ratings of the IS200BPIIH1AAA?
The definitive ratings depend on the exact configuration; consult the original datasheet or the source PDF linked on this page for the complete table.
How is the IS200BPIIH1AAA mounted or installed?
Installation follows the standard GE product portfolio mounting practice for this device class; refer to the installation manual for exact dimensions and torque.
Is the IS200BPIIH1AAA compatible with my controller?
It belongs to GE's automation product portfolio. Confirm the specific rack, firmware revision, slot rules and configuration with the controller documentation before purchase, as compatibility depends on the exact system build.
What should I check before buying the IS200BPIIH1AAA?
Verify the genuine part number and suffix, confirm it matches your platform and ratings, check the current lifecycle/availability status, and buy from an authorised distributor. PLCXpert provides this reference only and does not sell the component.
Specifications (source data)
IS200BPIIH1AAA Technical Specifications Manufacturer General Electric Series Mark VI Speedtronic Functional Part Number IS200BPIIH1AAA Functional Abbreviation BPIH Revision Total 3 Revisions Backwards-Compatibility 1st two revisions PCB Coating Style Conformal Coating
About the IS200BPIIH1AAA The IS200BPIIH1AAA, from the GE Speedtronic Mark VI series, is a Bridge Power Interface circuit board designed for use in Innovation Series drives. The Mark VI Turbine Control System Series that this IS200BPIIH1AAA Bridge Power Interface Board is ultimately a member of has to be defined as existing with a specific possible series of functional applications in the management and control systems of General Electric-compatible gas, steam, and wind turbine automated drive assemblies. This is quite the significant functional upgrade upon the previously-existing Mark V Turbine Control System Series of just about the same full extended series title, as the Mark VI Series added the alternative energy-focused wind turbine possible functional environment onto the gas and steam-based settings established with the rollout of the previous industry-standard Mark V Turbine Control System Series. This IS200BPIIH1AAA Bridge Power Interface Board PCB's Mark VI Series is also valued on greater relevant promotional markets for its status as one of the last-released GE Mark product series utilizing the patented Speedtronic control system technology across a wide range of products.
Hardware Tips and Specifications
The IS200BPIIH1AAA is used by the GGXI board to communicate gate command and status signals via RS-422 signals. The RS-422 drivers and receivers use point-to-point signaling that will alarm a bad gate signal if the cable is disconnected. The IS200BPIIH1AAA uses a serial prom ID chip and pull-up resistors. The resulting pull-up signal indicates that all cables are properly connected along the signal path. The IS200BPIIH1AAA has four connectors on its surface: two mounted in the front faceplate and two on its back edge. The rear connectors are 128-pin backplane connectors. Pin signal maps are available in GEI-100298. The two front connectors are designed to interface with the GGXI board. Each connector, labeled JGATE1 and JGATE2, has 68 pins. The front faceplate has no other mounted components but is marked with the GE logo, the board number, and with the proper location of the board (slot 6.) Improper seating of the board can damage the component. Do not insert it in the wrong slot. The board has no fuses, user test points, LED indicators, or adjustable hardware.
For more information about using or installing the IS200BPIIH1AAA, please refer to user guides, datasheets, or manuals originally supplied by General Electric with your OEM equipment. If these are no longer available, AX Control may be able to provide replacements with your order. Most orders for in-stock merchandise placed before 3 pm are shipped on the same day. In terms of its drivers and receivers, this IS200BPIIH1AAA Bridge Power Interface Board device drives and receives through the use of the standard style of RS-422 drivers and receivers as mentioned above. As with any General Electric Mark VI Turbine Control System or Innovation Series printed circuit board product offering available to our new and reconditioned extended inventory here, this IS200BPIIH1AAA Bridge Power Interface Board device is equipped with its own special series of installation and replacement specifications and procedures. For starters, and as with any relevant Mark VI Series product, this IS200BPIIH1AAA Bridge Power Interface Board device's installation should be conducted completely under the protection offered through a standard wrist grounding strap. This IS200BPIIH1AAA Bridge Power Interface Board printed circuit board product offering is also deemed to fit in a specific VME Rack installation assembly rack slot, with its installation secured through two screw standoffs as pictured above.
Reproduced from the manufacturer's published data.