IC697RCM711
GE
Overview
The IC697RCM711 is a Communication Module from GE. It extends the GE product portfolio connectivity through its onboard communication interface.
Application & Technical Notes
As a communication module, the IC697RCM711 is intended for deployment in panel-based control cabinets and machine enclosures where the GE product portfolio equipment is installed. It bridges the controller to higher-level networks, HMIs, SCADA and peer devices, carrying configuration, process data and diagnostics.
Specific electrical and mechanical ratings depend on the exact configuration and suffix of the part; the original datasheet should be consulted for the definitive specification.
Maintenance & Diagnostics
Confirm network addressing, baud/rate and topology match the rest of the system; keep firmware consistent across the cell. Always de-energise the circuit and follow lock-out/tag-out before handling; refer to the official instruction bulletin for service procedures.
Sourcing & Procurement
When sourcing the IC697RCM711, distinguish three supply tiers: (1) genuine GE stock from an authorised distributor; (2) compatible equivalents or surplus/NOS (new-old-stock) from third parties; (3) alternative parts offering equivalent function. Genuine supply carries the full warranty and traceability; compatible or alternative items may be cheaper but should be validated for form, fit, firmware and certification before use in a live system. PLCXpert publishes this page as an independent reference and does not sell the part — verify every claim with the manufacturer or your distributor.
Match the protocol, connector and topology to the rest of the GE product portfolio network and to the peer devices already installed. Lead times and pricing vary by region and lifecycle status; obtain a current quote from an authorised channel rather than relying on stale listings.
Check live stock, lead time and request a quote for IC697RCM711 (opens in a new tab)
Frequently Asked Questions
What is the IC697RCM711?
The IC697RCM711 is a communication module from GE. It is described by the manufacturer as: Communication Module.
What are the key technical ratings of the IC697RCM711?
The definitive ratings depend on the exact configuration; consult the original datasheet or the source PDF linked on this page for the complete table.
How is the IC697RCM711 mounted or installed?
Installation follows the standard GE product portfolio mounting practice for this device class; refer to the installation manual for exact dimensions and torque.
Is the IC697RCM711 compatible with my controller?
It belongs to GE's automation product portfolio. Confirm the specific rack, firmware revision, slot rules and configuration with the controller documentation before purchase, as compatibility depends on the exact system build.
What should I check before buying the IC697RCM711?
Verify the genuine part number and suffix, confirm it matches your platform and ratings, check the current lifecycle/availability status, and buy from an authorised distributor. PLCXpert provides this reference only and does not sell the component.
Specifications (source data)
The IC697RCM711 is a Redundancy Communication module from the Series 90-70 Programmable Logic Controller (PLC) platform that is formerly manufactured by GE Fanuc, now under Emerson Automation. This module features a high-speed parallel bus expansion interface and supports operating with hot Standby and Enhanced Hot Standby CPU systems. Technical specifications for IC697RCM711 Brand GE Fanuc Series Series 90-70 Manufacturer GE Fanuc (Former); Emerson Automation (Current) Part Number IC697RCM711 Series Series 90-70 Type Communication Module Product Description Redundancy Communication Module (RCM) Purpose Redundancy system Maximum cable length 50 feet (15 meters) Current required from 5V Bus 1.2 A Backplane Current draw 1.2 Amperes Maximum cable length 15 m Compatible Controllers IC697CPU780, IC697CGR772 and IC697CGR735 Effective data rate 500 Kbytes / sec Compatible Bus Transmitter Module IC697BEM713 Electrical isolation Non-isolated differential communication Compatible communication cable IC600WD005 / 010 / 025 / 050 cables VME Supported Terminating plug IC697ACC702 Status indicators Yes Cable with termination IC697CBL811 / IC697CBL826 Pushbutton Yes LED indicators OK, Local Ready, Local Active, remote Ready and Remote Active LED Product Lifecycle Discontinued The IC697RCM711 is a Redundancy Communications Module (RCM). It is part of the Series 90-70 Programmable Logic Controller (PLC) series, featuring a High-Speed Parallel Bus Expansion Interface, specially designed for use with Hot Standby and Enhanced Hot Standby CPU redundancy configuration. This module provides a synchronization path and I/O update path between the partner CPUs, contributing to rapid update and bumpless transfer of CPU control during the event of a switchover. The IC697RCM711 is part of a redundancy system that is typically comprised of Hot Standby Series 90-70 Controllers such as IC697CPU780, IC697CGR772, and IC697CGR735; Bus Transmitter Module with catalog number IC697BEM713 along with a Bus Terminator Plug with catalog number IC697ACC702. Up to 50 feet or 15 meters maximum cable distance is permitted between each CPU however, several cables are available for use with the RC< module including IC600WD005 / 010 / 025 / 050 cables with lengths of 5 feet or 1.5 meters; 10 feet of 3 meters; 25 feet of 7.5 meters and to 50 feet or 15 meters. Optionally, I/O cables with integrated terminating resistors can be used such as IC697CBL811 with a length of 10 feet or 3 meters or IC697CBL826 with a length of 25 feet or 7.5 meters. This module has built-in Status LED indicators such as OK, Local Ready, Local Active, remote Ready, and Remote Active LED indicators. It has Two (2) ports installed with 1 being a dummy port and a communication port that supports the connection of Expansion port IN. this module also has a manual pushbutton switch that can be triggered to initiate manual switchover from active to backup module.
The IC697RCM711 module is a redundancy communications module in the Series 90-70 product line by GE Fanuc Automation. The IC697RCM711 communications module is generally used in applications that include a Hot Standby or an Enhanced Hot Standby CPU Redundancy system. Both of these systems can have a connection length of at least 7.5 meters which enables them to be located in different areas if needed. The CPUs that support this kind of operation are the IC697CPU780, IC697CGR935, and the IC697CGR772 CPU. The GE Fanuc Automation Series 90-70 IC697RCM711 communications module requires a current of 1.2 Amps and a Bus voltage of 5 Volts and it also comes with an expansion interface that uses a 15-meter connection cable. This module can communicate at a data rate of 500 KB per second and it does not require specific electrical isolation in order to operate. This module has been designed to operate with the VME integrated devices. The GE Fanuc Automation IC697RCM711 communications module comes with status indicators and a physical pushbutton. Through these buttons, the current state of the system can be changed from the main unit to the backup unit and vice versa.
Reproduced from the manufacturer's published data.