IC695PSD140

AI-generated · verify with manufacturerLast reviewed 2026-09-29

Overview

The IC695PSD140 is a Power supply module from GE. It delivers stable control power at range 85 to 264 VAC 100 to 300 VDC for the GE product portfolio racks.

Application & Technical Notes

As a power supply module, the IC695PSD140 is intended for deployment in panel-based control cabinets and machine enclosures where the GE product portfolio equipment is installed. It conditions and distributes the low-voltage supply that powers the controller, I/O and communication modules on the same rack.

Key published characteristics include a range 85 to 264 VAC 100 to 300 VDC rating. These values should be confirmed against the current manufacturer datasheet before final selection, as options and suffixes vary by configuration.

Maintenance & Diagnostics

Ensure adequate ventilation and do not overload the supply beyond its published current budget; consider redundancy for critical racks. Always de-energise the circuit and follow lock-out/tag-out before handling; refer to the official instruction bulletin for service procedures.

Sourcing & Procurement

When sourcing the IC695PSD140, distinguish three supply tiers: (1) genuine GE stock from an authorised distributor; (2) compatible equivalents or surplus/NOS (new-old-stock) from third parties; (3) alternative parts offering equivalent function. Genuine supply carries the full warranty and traceability; compatible or alternative items may be cheaper but should be validated for form, fit, firmware and certification before use in a live system. PLCXpert publishes this page as an independent reference and does not sell the part — verify every claim with the manufacturer or your distributor.

Match the output voltage and current to the GE product portfolio load and allow headroom for future expansion. Lead times and pricing vary by region and lifecycle status; obtain a current quote from an authorised channel rather than relying on stale listings.

Check live stock, lead time and request a quote for IC695PSD140 (opens in a new tab)

Frequently Asked Questions

What is the IC695PSD140?

The IC695PSD140 is a power supply module from GE. It is described by the manufacturer as: Power supply module.

What are the key technical ratings of the IC695PSD140?

Its published highlights include range 85 to 264 VAC 100 to 300 VDC. Full electrical, mechanical and environmental limits are listed in the manufacturer datasheet and should be confirmed for your exact suffix.

How is the IC695PSD140 mounted or installed?

Installation follows the standard GE product portfolio mounting practice for this device class; refer to the installation manual for exact dimensions and torque.

Is the IC695PSD140 compatible with my controller?

It belongs to GE's automation product portfolio. Confirm the specific rack, firmware revision, slot rules and configuration with the controller documentation before purchase, as compatibility depends on the exact system build.

What should I check before buying the IC695PSD140?

Verify the genuine part number and suffix, confirm it matches your platform and ratings, check the current lifecycle/availability status, and buy from an authorised distributor. PLCXpert provides this reference only and does not sell the component.

Specifications

The IC695PSD140 is a PACSystems RX3i Power Supply module that is manufactured by Emerson Automation, formerly by GE Intelligent Platforms (GE IP). This module is specifically a DC power supply, designed for an input voltage range of 18-30 VDC and maximum input power of 60 Watts at full load. It has a nominal output current and voltage of 0-6 A @ 5.1 VDC and 0-9 A @ 3.3 VDC. It also has a 24VDC voltage output for power circuits and output relay modules and maximum output power of 40 Watts. This module supports load sharing and redundancy applications

Description

Note	The IC695PSD140 is an Emerson Automation manufactured Power supply module that is part of the PACsystem RX3i PAC platform. This module is specifically a Universal base power supply that is compatible for use with any RX3i Central Processing Unit (CPU). This module does not have jumper or DIP switches to define the module’s operation. The IC695PSD140 occupies Two (2) slot of the chassis. It is powered by an external supply voltage of 100-240 VAC or 0-125 VDC and it delivers an output power rated 40 Watts with 30 Watts at 3.3 VDC; 30 Watts at 5VDC and 40 Watts at 24 VDC relay. Up to Four (4) multi-purpose power supply can be installed to a RX3i universal backplane for use in application that require redundancy and increased capacity modes. When configured in load sharing architecture, the IC695PSD140’s On/ Off switch installed on the front panel must not be turned Off inadvertently. The minimum number of power supply must be maintained On to qualify the system. Additionally, for the same configuration, power supply modules must be connected to the same power source. This power supply has output ripple of 150 mV and noise measured at 150 mV while the ride-through time is 20 ms. Power ride through time refers to the capability of the power supply to supply sufficient power despite interruption in the supply line. When terminating connections to the power supply terminal, recommended wire size range is #14 - 22 AWG wire. The maximum current each input terminal can accommodate is 6 Amperes. The IC695PSD140 module is a multipurpose power supply module that comes in the RX3i PACSystems series of I/O devices. This part has been designed and manufactured by GE Fanuc Automation. This module can operate both in load-sharing and redundancy applications, hence its multipurpose tag. It comes with 3 different outputs that consist of a 5.1 Volts DC output, a 24 Volts DC relay output, and a 3.3. Volts DC output intended for internal use. These 3 outputs can be used with RX3i modules. The GE Fanuc Automation IC695PSD140 multipurpose power supply module can be installed in an RX3i universal backplane and it only occupies one slot. It can be used as the only power supply in a system or it can be combined with additional multipurpose power supplies. It can be combined with up to 3 other modules. The GE Fanuc Automation IC695PSD140 multipurpose power supply module comes with several LED indicators. The power LED can be green or amber, the P/S fault and overload LED is red, and the over-temperature and overload LED is an amber indicator. Each LED indicates the current operating status of the module. The module has a nominal rated voltage of 24 Volts DC, an input voltage range of 18 to 30 Volts DC, and an output power rating of 40 Watts maximum, including its 3 outputs. The module does not provide isolation. It is important to note that the GE Fanuc Automation IC695PSD140 multipurpose power supply cannot be used under any circumstances with the IC695PSD040 or the IC695PSA040 power supply modules in a redundant mode or in an increased capacity mode. These modules are incompatible in these modes and damage to both types of equipment may occur if the users attempt to use them in these modes.

Note

The IC695PSD140 is an Emerson Automation manufactured Power supply module that is part of the PACsystem RX3i PAC platform. This module is specifically a Universal base power supply that is compatible for use with any RX3i Central Processing Unit (CPU). This module does not have jumper or DIP switches to define the module’s operation. The IC695PSD140 occupies Two (2) slot of the chassis. It is powered by an external supply voltage of 100-240 VAC or 0-125 VDC and it delivers an output power rated 40 Watts with 30 Watts at 3.3 VDC; 30 Watts at 5VDC and 40 Watts at 24 VDC relay. Up to Four (4) multi-purpose power supply can be installed to a RX3i universal backplane for use in application that require redundancy and increased capacity modes. When configured in load sharing architecture, the IC695PSD140’s On/ Off switch installed on the front panel must not be turned Off inadvertently. The minimum number of power supply must be maintained On to qualify the system. Additionally, for the same configuration, power supply modules must be connected to the same power source. This power supply has output ripple of 150 mV and noise measured at 150 mV while the ride-through time is 20 ms. Power ride through time refers to the capability of the power supply to supply sufficient power despite interruption in the supply line. When terminating connections to the power supply terminal, recommended wire size range is #14 - 22 AWG wire. The maximum current each input terminal can accommodate is 6 Amperes. The IC695PSD140 module is a multipurpose power supply module that comes in the RX3i PACSystems series of I/O devices. This part has been designed and manufactured by GE Fanuc Automation. This module can operate both in load-sharing and redundancy applications, hence its multipurpose tag. It comes with 3 different outputs that consist of a 5.1 Volts DC output, a 24 Volts DC relay output, and a 3.3. Volts DC output intended for internal use. These 3 outputs can be used with RX3i modules. The GE Fanuc Automation IC695PSD140 multipurpose power supply module can be installed in an RX3i universal backplane and it only occupies one slot. It can be used as the only power supply in a system or it can be combined with additional multipurpose power supplies. It can be combined with up to 3 other modules. The GE Fanuc Automation IC695PSD140 multipurpose power supply module comes with several LED indicators. The power LED can be green or amber, the P/S fault and overload LED is red, and the over-temperature and overload LED is an amber indicator. Each LED indicates the current operating status of the module. The module has a nominal rated voltage of 24 Volts DC, an input voltage range of 18 to 30 Volts DC, and an output power rating of 40 Watts maximum, including its 3 outputs. The module does not provide isolation. It is important to note that the GE Fanuc Automation IC695PSD140 multipurpose power supply cannot be used under any circumstances with the IC695PSD040 or the IC695PSA040 power supply modules in a redundant mode or in an increased capacity mode. These modules are incompatible in these modes and damage to both types of equipment may occur if the users attempt to use them in these modes.

Reproduced from the manufacturer's published data. Values marked "Not available" are absent from the source document.