IC695PRS015

AI-generated · verify with manufacturerLast reviewed 2026-09-29

Overview

The IC695PRS015 is a Pressure Transducer Module in the RX3i range from GE. It is part of GE's industrial automation product portfolio.

Application & Technical Notes

As a pressure transducer module, the IC695PRS015 is intended for deployment in panel-based control cabinets and machine enclosures where the GE product portfolio equipment is installed. It performs a defined automation function within the control system and is selected to match the installed GE platform.

Specific electrical and mechanical ratings depend on the exact configuration and suffix of the part; the original datasheet should be consulted for the definitive specification.

Maintenance & Diagnostics

Verify field wiring, shielding and grounding at installation; check terminal torque and confirm signal types match the configured range. Periodically inspect for loose terminations, induced noise and channel-level diagnostics reported by the controller. Always de-energise the circuit and follow lock-out/tag-out before handling; refer to the official instruction bulletin for service procedures.

Sourcing & Procurement

When sourcing the IC695PRS015, distinguish three supply tiers: (1) genuine GE stock from an authorised distributor; (2) compatible equivalents or surplus/NOS (new-old-stock) from third parties; (3) alternative parts offering equivalent function. Genuine supply carries the full warranty and traceability; compatible or alternative items may be cheaper but should be validated for form, fit, firmware and certification before use in a live system. PLCXpert publishes this page as an independent reference and does not sell the part — verify every claim with the manufacturer or your distributor.

Confirm the module matches your GE product portfolio rack, the required channel count, signal type and voltage, and the firmware/configuration of the controller. Lead times and pricing vary by region and lifecycle status; obtain a current quote from an authorised channel rather than relying on stale listings.

Check live stock, lead time and request a quote for IC695PRS015 (opens in a new tab)

Frequently Asked Questions

What is the IC695PRS015?

The IC695PRS015 is a pressure transducer module in the RX3i range from GE. It is described by the manufacturer as: Pressure Transducer Module.

What are the key technical ratings of the IC695PRS015?

The definitive ratings depend on the exact configuration; consult the original datasheet or the source PDF linked on this page for the complete table.

How is the IC695PRS015 mounted or installed?

Installation follows the standard GE product portfolio mounting practice for this device class; refer to the installation manual for exact dimensions and torque.

Is the IC695PRS015 compatible with my controller?

It belongs to GE's automation product portfolio. Confirm the specific rack, firmware revision, slot rules and configuration with the controller documentation before purchase, as compatibility depends on the exact system build.

What should I check before buying the IC695PRS015?

Verify the genuine part number and suffix, confirm it matches your platform and ratings, check the current lifecycle/availability status, and buy from an authorised distributor. PLCXpert provides this reference only and does not sell the component.

Specifications

The IC695PRS015 pressure transducer module is manufactured by the GE Fanuc as part of the RX3i PacSystem series. This module expands the RX3i system serial communications capabilities to enable communication with up to 15 Honeywell smart pressure transducer sensors.

Description

Note	The IC695PRS015 module is a pressure transducer module. It is a product of GE Fanuc and it belongs to the RX3i PacSystem product line. It is used to expand the RX3i PacSystem setup's serial communications capabilities and it has a single slot and an RJ-45 port to enable communication with up to 15 Honeywell (LG1237) smart pressure transducer sensors. This module has a power consumption rating of 0.7 Amps at 3.3 Volts DC or 0.115 Amps at 5 Volts DC, and up to 4 modules are supported in the main CPU backplane and a minimum channel to channel crosstalk of -55 dB, a maximum overvoltage of -/+ 25 Volts, and a baud rate of 375 kilo-baud. The IC695PRS015 module provides independent, isolated serial ports, and the main RX3i backplane can only contain a maximum of 4 pressure transducer modules. Other notable features of the IC695PRS015 pressure transducer module includes port to backplane isolation, flash memory for upgrades, support for hot insertion and hot removal, and an RS-485 communication port. It also receives module status, identity, and fault reports from the LED indicators. The GE Fanuc IC695PRS015 pressure transducer module is located in the RX3i PacSystem universal backplane. It comes with LED indicators which are the "MODULE OK," "PORT FAULT," and the "PORT STATUS" indicators. The "MODULE OK" LED indicator shows the module's status. It turns off when the module fails the self-test or when it does not receive power from the RX3i PacSystem backplane. The "MODULE OK" LED turns green after the configuration of the module, it blinks green rapidly when the module is executing the power diagnostics, and it blinks green slowly when the module has not been configured properly from the CPU. The "PORT FAULT" LED indicator shows the port status with a green light for no fault or for an enabled port and it glows amber for a fault on the port.

Note

The IC695PRS015 module is a pressure transducer module. It is a product of GE Fanuc and it belongs to the RX3i PacSystem product line. It is used to expand the RX3i PacSystem setup's serial communications capabilities and it has a single slot and an RJ-45 port to enable communication with up to 15 Honeywell (LG1237) smart pressure transducer sensors. This module has a power consumption rating of 0.7 Amps at 3.3 Volts DC or 0.115 Amps at 5 Volts DC, and up to 4 modules are supported in the main CPU backplane and a minimum channel to channel crosstalk of -55 dB, a maximum overvoltage of -/+ 25 Volts, and a baud rate of 375 kilo-baud. The IC695PRS015 module provides independent, isolated serial ports, and the main RX3i backplane can only contain a maximum of 4 pressure transducer modules. Other notable features of the IC695PRS015 pressure transducer module includes port to backplane isolation, flash memory for upgrades, support for hot insertion and hot removal, and an RS-485 communication port. It also receives module status, identity, and fault reports from the LED indicators. The GE Fanuc IC695PRS015 pressure transducer module is located in the RX3i PacSystem universal backplane. It comes with LED indicators which are the "MODULE OK," "PORT FAULT," and the "PORT STATUS" indicators. The "MODULE OK" LED indicator shows the module's status. It turns off when the module fails the self-test or when it does not receive power from the RX3i PacSystem backplane. The "MODULE OK" LED turns green after the configuration of the module, it blinks green rapidly when the module is executing the power diagnostics, and it blinks green slowly when the module has not been configured properly from the CPU. The "PORT FAULT" LED indicator shows the port status with a green light for no fault or for an enabled port and it glows amber for a fault on the port.

Reproduced from the manufacturer's published data. Values marked "Not available" are absent from the source document.