IC695CHS012

AI-generated · verify with manufacturerLast reviewed 2026-09-29

Overview

The IC695CHS012 is an Universal backplane from GE. It is part of GE's industrial automation product portfolio.

Application & Technical Notes

As an universal backplane, the IC695CHS012 is intended for deployment in panel-based control cabinets and machine enclosures where the GE product portfolio equipment is installed. It mechanically and electrically unifies the controller, power supply and I/O modules, providing the backplane bus and mounting structure.

Specific electrical and mechanical ratings depend on the exact configuration and suffix of the part; the original datasheet should be consulted for the definitive specification.

Maintenance & Diagnostics

Seat every module firmly on the backplane, observe module order where required, and check the bus connector integrity. Always de-energise the circuit and follow lock-out/tag-out before handling; refer to the official instruction bulletin for service procedures.

Sourcing & Procurement

When sourcing the IC695CHS012, distinguish three supply tiers: (1) genuine GE stock from an authorised distributor; (2) compatible equivalents or surplus/NOS (new-old-stock) from third parties; (3) alternative parts offering equivalent function. Genuine supply carries the full warranty and traceability; compatible or alternative items may be cheaper but should be validated for form, fit, firmware and certification before use in a live system. PLCXpert publishes this page as an independent reference and does not sell the part — verify every claim with the manufacturer or your distributor.

Confirm mechanical and electrical compatibility with your GE product portfolio installation and the intended function. Lead times and pricing vary by region and lifecycle status; obtain a current quote from an authorised channel rather than relying on stale listings.

Check live stock, lead time and request a quote for IC695CHS012 (opens in a new tab)

Frequently Asked Questions

What is the IC695CHS012?

The IC695CHS012 is an universal backplane from GE. It is described by the manufacturer as: Universal backplane.

What are the key technical ratings of the IC695CHS012?

The definitive ratings depend on the exact configuration; consult the original datasheet or the source PDF linked on this page for the complete table.

How is the IC695CHS012 mounted or installed?

Installation follows the standard GE product portfolio mounting practice for this device class; refer to the installation manual for exact dimensions and torque.

Is the IC695CHS012 compatible with my controller?

It belongs to GE's automation product portfolio. Confirm the specific rack, firmware revision, slot rules and configuration with the controller documentation before purchase, as compatibility depends on the exact system build.

What should I check before buying the IC695CHS012?

Verify the genuine part number and suffix, confirm it matches your platform and ratings, check the current lifecycle/availability status, and buy from an authorised distributor. PLCXpert provides this reference only and does not sell the component.

Specifications

The GE Fanuc / Emerson Automation IC695CHS012 is a PACSystem RX3i universal backplane. This backplane features 12-slots of high-speed controller base, supporting PCI and serial bus. This backplane supports hot swapping of modules power consumption of 600 mA @ 3.3 VDC and 240 mA @ 5 VDC.

Description

Note	The IC695CHS012 is a PACSystem RX3i universal backplane. This Backplane features 12 slots that supports high-speed Peripheral Component Interconnect (PCI) and serial bus connection. Backplanes are necessary components as it provides housing to the RX3i modules and connectivity. It also hosts the communication bus where internal communication between modules takes place. The IC695CHS012 has a power consumption of 600 mA @ 3.3 VDC and 240 mA @ 5 VDC. It has physical dimensions of 18.01 x 5.57 x 5.80 (457.5 x 141.5 x 147.32) and supports horizontal mounting. It mut be mounted inside an enclosure that offers IP20 / NEMA/UL Type 1 Protection rating. For natural cooling and promote adequate air circulation, the backplane must have 102 mm or 4 inches clearance on all sides of the hardware. For ATEX Zone 2 Hazardous area requirements, the IC695CHS012 must be installed inside an IP54 or greater enclosure with mechanical strength to withstand 3.5 Joules of impact energy. The IC695CHS012 supports hot-swapping of module or removable and insertion under power. This provides a distinct advantage as it effectively reduces downtime and permits maintenance activities such as module replacement and integrity verification to be carried out without affecting the present operating mode of the attached controller and modules. Additionally, this backplane supports installation of optional baseplate such as controller base and ethernet expansion base. The IC695CHS012 backplane is provided with a TB1 terminal block that allows termination of optional external 24VDC power source for use by some IC693 and IC694 modules . Recommended wires for use is AWG 14-22 individual wires. The IC695CHS012 backplane has an internal current rating of 240 milliamps at 5 Volts DC and a current rating of 600 milliamps at 3.3 Volts DC. The backplane must be positioned horizontally and it requires at least 102 millimeters (4 inches) of space on all sides in order to perform properly and to be air-cooled. The supported input terminals used with IC695CHS012 universal backplane use individual wires in sizes from 14 to 22 AWG. The terminals in slots 7 and 8 are typically used for isolated external power sources. Every slot in the IC695CHS012 backplane is configured to accept different components, for example, DC power supplies are connected to a single slot, but AC power supplies are intended for 2 slots.

Note

The IC695CHS012 is a PACSystem RX3i universal backplane. This Backplane features 12 slots that supports high-speed Peripheral Component Interconnect (PCI) and serial bus connection. Backplanes are necessary components as it provides housing to the RX3i modules and connectivity. It also hosts the communication bus where internal communication between modules takes place. The IC695CHS012 has a power consumption of 600 mA @ 3.3 VDC and 240 mA @ 5 VDC. It has physical dimensions of 18.01 x 5.57 x 5.80 (457.5 x 141.5 x 147.32) and supports horizontal mounting. It mut be mounted inside an enclosure that offers IP20 / NEMA/UL Type 1 Protection rating. For natural cooling and promote adequate air circulation, the backplane must have 102 mm or 4 inches clearance on all sides of the hardware. For ATEX Zone 2 Hazardous area requirements, the IC695CHS012 must be installed inside an IP54 or greater enclosure with mechanical strength to withstand 3.5 Joules of impact energy. The IC695CHS012 supports hot-swapping of module or removable and insertion under power. This provides a distinct advantage as it effectively reduces downtime and permits maintenance activities such as module replacement and integrity verification to be carried out without affecting the present operating mode of the attached controller and modules. Additionally, this backplane supports installation of optional baseplate such as controller base and ethernet expansion base. The IC695CHS012 backplane is provided with a TB1 terminal block that allows termination of optional external 24VDC power source for use by some IC693 and IC694 modules . Recommended wires for use is AWG 14-22 individual wires. The IC695CHS012 backplane has an internal current rating of 240 milliamps at 5 Volts DC and a current rating of 600 milliamps at 3.3 Volts DC. The backplane must be positioned horizontally and it requires at least 102 millimeters (4 inches) of space on all sides in order to perform properly and to be air-cooled. The supported input terminals used with IC695CHS012 universal backplane use individual wires in sizes from 14 to 22 AWG. The terminals in slots 7 and 8 are typically used for isolated external power sources. Every slot in the IC695CHS012 backplane is configured to accept different components, for example, DC power supplies are connected to a single slot, but AC power supplies are intended for 2 slots.

Reproduced from the manufacturer's published data. Values marked "Not available" are absent from the source document.